 |
|
| System hang on USB storage access |
|
|
By tigerdog - Posted on July 2, 2004 - 22:39:37 (#13192)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
I've installed the driver (under Dano) using defaults. When I place an SD card into the reader, the card mounts. I can move very small files (<15K) onto or off of the drive. As soon as I try to move anything larger, the drive access light stays on solid and the file transfer hangs. Moreover, while I can sometimes get the system to shut down, it will not restart until I either unplug the reader's USB cable or power the entire system off and back on.
Suggestions, please?
|
|
| matjako |
|
|
By zharik - Posted on June 25, 2004 - 09:41:05 (#13022)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
This device looks as supported. Can you, please, obtain the log file of working session with this camera and sent it to me on <imker [@] gmx.li>? Thanks.
|
|
| Is this right? |
|
|
By matjako - Posted on June 25, 2004 - 09:02:36 (#13021)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Hi, usb_scsi driver works great for me on some USB flash drive, but not on my NikonCoolpix 3100 (mass storage mode). Any ideas? I left the deafult settings for the driver as was... the usb_dev_info says:
Class .................. 0
Subclass ............... 0
Protocol ............... 0
Vendor ID .............. 0x04b0
Product ID ............. 0x0114
Version ................ 0x0100
Manufacturer String .... "NIKON"
Product String ......... "NIKON DSC E3100"
Serial Number .......... "000004931562"
[Configuration 0]
[Interface 0]
Class .............. 8
Subclass ........... 6
Protocol ........... 80
[Endpoint 0]
MaxPacketSize .... 64
Interval ......... 0
Type ............. Bulk
Direction ........ Output
[Endpoint 1]
MaxPacketSize .... 64
Interval ......... 0
Type ............. Bulk
Direction ........ Input
|
|
| Vivitar ViviCam 3750 Works |
|
|
By Moriarty - Posted on June 20, 2004 - 19:19:41 (#12974)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Hello... Just a piece of info about an additional camera that works with this driver... A Vivitar ViviCam 3750 (A 3.1 Megapixel Camera, around $100 USD at Wal-Mart) - Works perfectly on Zeta RC2 (Don't know about RC3, or any patched versions of R5.03)... All I had to do was remove the native Zeta USB SCSI driver (as poster earlier in this forum) reboot, and instant sucess...
Thanks to everyone for this driver and for the tip... Now perhaps I can get my wife off of Linux and onto a real OS!
Cheers!
Brian
|
|
| Re: Mount speed |
|
|
By tb100 - Posted on June 20, 2004 - 17:56:21 (#12973)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
To increase the speed of the mount menu - reduce the number of virtual devices in the driver's config file (see readme). I set both devices and luns to 1 as I only have a single usb mass storage device (a digital camera) - the mount menu appears much more quickly.
|
|
| WooHoo! (Zeta RC3) |
|
|
By leonifan - Posted on June 20, 2004 - 13:47:42 (#12972)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Yep, you were right there - removing the Zeta usb-scsi solves the problem completely - and with Zeta this release, it *appears* I even get USB2.0 speeds!
It also seems to speed up the Mount list from the desktop. I will of course let you know of any other things that pop up, but once again - extreme thanks for a great driver!
Actually, I reckon you should get money for this - plenty of other driver writers charge a (usually small) fee for their work. Set up a PayPal account or something, and I'll give you a donation - 10 Euros or summat.
What do others think about this? (Hope I don't start a flame war..!)
|
|
| leonifan |
|
|
By zharik - Posted on June 20, 2004 - 13:10:06 (#12971)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Looks strange.
Have you tried to disable Zeta's usb_scsi?
To do this rename the following file:
/boot/beos/system/add-ons/kernel/busses/scsi/usb to /boot/beos/system/add-ons/kernel/busses/scsi/usb.disabled or remove it from this directory.
The way you can obtain the log file is described in details in ReadMe.html from my module distribution archive.
It is a good idea to send me the log you'll get to my e-mail address <imker( at )gmx.li>. Thanks.
|
|
| Zeta RC3 |
|
|
By leonifan - Posted on June 19, 2004 - 22:02:38 (#12968)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Sadly, using this driver with the latest version of Zeta no longer seems to work for me :(
Zeta RC3 does not work with my USB flash drive. Unfortunately, unlike with RC2, this driver doesn't make it work either.
(On the plus side, Zeta now works fine with my Olympus C-350 camera in USB1.1 or USB2.0 ports from a clean install \o/).
Of course you can only fix this once you have a copy of RC3 yourself...
If it will help, I can run the logging utility?
Also, on a different note, I have noticed that the driver seems to take a very long time before bringing up the Mount drive list from the desktop. It did this on RC2 as well, though.
Thanks
Mark
|
|
| ernestTX |
|
|
By zharik - Posted on June 18, 2004 - 19:43:29 (#12963)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
The problem is that USB stack version 3 from USB patches doesn't work correctly with devices, that want support of USB version 2(that one that plain R5 has). Yes - there is a kind of backward compatibility layer for version 2 in USB patches, but looks like it doesn't help. I suspect, that there are no life possibilities for old (v2) devices under USB patches at all. =-\
|
|
| one or the other |
|
|
By ernestTX - Posted on June 18, 2004 - 19:20:28 (#12962)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
zharik,
looks like the Tablet Driver from Becasso that resides in /boot/home/config/add-ons/kernel/input_server/devices does not play well with USB Patches. I remove it all works well, however tablet is quirky. If I re-add it, KDL. Unsure whether you can look into this or not. Let me know if you need any information.
|
|
| Intuix DiskOnKey work nice... |
|
|
By cvincent - Posted on June 18, 2004 - 19:02:06 (#12960)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Hi, just little talkback to say yeah !! my USB key Intuix DiskOnKey 256Mo Work nice.
(i just have the problem about SCSI card + driver but you know ;)
|
|
| matjako |
|
|
By zharik - Posted on June 18, 2004 - 18:26:59 (#12959)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
could you, please, show me the info from USBCommander or usb_dev_info ?
|
|
| 50% success |
|
|
By matjako - Posted on June 18, 2004 - 15:48:22 (#12957)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Great work, my cheapo 256 USB drive works great, however
I can't get to work my Nikon Coolpix 3100 in Mass Storage mode. USBCommander returns same protocol and class numbers for both devices. I believe there is one entry less in endpoints configuration for Coolpix (1 input 1 output)
Otherwise, well done!
|
|
| Umm...... |
|
|
By animerules - Posted on June 18, 2004 - 13:54:13 (#12954)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
An O'rite Digital Cam Pro, I think its cheap one, 3.1 megapixel. Came with our new pc and I just decided to have it since my parents already had one.
|
|
| animerules |
|
|
By zharik - Posted on June 18, 2004 - 13:44:48 (#12953)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Which camera do you tried?
|
|
| THANKYOU |
|
|
By animerules - Posted on June 18, 2004 - 13:27:41 (#12952)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
thanx, I seriously thought I'd never get my digital camera to work in BeOS. I'm uaing BeOS R5.0.3
|
|
| Found the culprit |
|
|
By ernestTX - Posted on June 18, 2004 - 06:51:53 (#12950)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
It seems that after I did complete fresh install of BeOS 5.0.3 and I began to re-install my applications, I found the culprit that was throwing me into KDL - BeCasso's tablet driver.
I first installed Wonderbrush, no prob. Then Refraction, no prob. I then installed BeCasso; however, at first I did not install the Wacom tablet driver. Everything seemed to be chugging along fine. However, I had this nasty problem that I was unable to setup Wonderbrush as the photo edit app in eXposer. Tried and tried, but I could not figure it out. It was always using BeCasso to edit. So, finally, I wanted to use my Wacom tablet. So I unmounted my SD Memory reader and plugged in my tablet.
Knowing that I needed some tablet preferences, I re-installed Becasso. This time I opted to load tablet driver. It went OK. However, when I opened Tablet Preferences, kdl land. I rebooted. KDL land. I rebooted, safe mode and looked to see where tablet driver was and removed it. Rebooted and back to desktop area.
Will keep testing away. I love a good mystery. :)
|
|
| Success finally :) |
|
|
By ernestTX - Posted on June 18, 2004 - 02:40:48 (#12947)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Ok, basically nothing beats just starting over from the beginning. I did a fresh install of 5.0, updated to 5.0.3. Removed any cards that would cause IRQ conflicts and then install USB Patches. That worked. Now onto the USB Mass Storage driver. Rebooted and got KDL. Then edited settings file for init 2 thingy and rebooted. Back up to desktop. Now to plug in my card reader with SD card full of pictures from JVC GRDVP3U. Right click to Mount and it showed up. Able to access card and I don't see any lag with accessing picture files. Thank you so much for this driver and for the help. This is why I love BeOS and its community. You get a huge YOU ROCK!
|
|
| ernestTX |
|
|
By zharik - Posted on June 17, 2004 - 09:02:20 (#12928)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
- R5 means R5.0.3 of course.
- Unfortunately I have no more ideas but trying to aply patches on fresh installed R5(R5.0.3). Probably some previously installed drivers make problems.
Note that only patch-1 is required for you.
anybody have more ideas?
|
|
| Arrgghh hehe |
|
|
By ernestTX - Posted on June 17, 2004 - 03:22:42 (#12925)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Ok let's see...I searched for any usb_mass or any other usb thingy. Deleted USBCommander and USB Deskview just to be sure.
I am only trying to apply patches, not usb mass storage driver.
Am I correct in referring that this only works for BeOS 5.0, and will not work with 5.0.3?
|
|
| MoerBoer...THX |
|
|
By beforum_VBL! - Posted on June 16, 2004 - 18:27:09 (#12910)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
I did what you recommended by changing the init file.
It worked.
|
|
| ernest_TX |
|
|
By tb100 - Posted on June 16, 2004 - 16:44:35 (#12907)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
That was the problem I had too - you have an old usb mass storage driver installed. Do a serach for usb_mass and delete it.
|
|
| USB patches |
|
|
By vasper - Posted on June 16, 2004 - 16:44:13 (#12906)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
You shouldn't apply all the 3 files in the patch. One of them sends R5 to KDL. I don't remember which one though. It must be in a readme or something...
|
|
| ernestTX |
|
|
By zharik - Posted on June 16, 2004 - 16:10:21 (#12905)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Did you tried this on clen-installed R5?
|
|
| Still no go on ASUS A7V133 |
|
|
By ernestTX - Posted on June 16, 2004 - 05:40:11 (#12900)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Well, tried your suggestions on applying patches, but get kdl each time:
kernel debugger
eax 00000000 ebp fc017f40 cs 0008 | area 0567cdb8 (usb_seg0)
ebx 600b305c esp fc017f10 ss 0010 | addr 600a8000 size 0000a0000
ecx 011cb258 edi 011c9000 ds 0010 |
edx 0117a1d8 esi 0117a1ec es 0010 | Thread:UHCD_DPC
eip 600adf45 flag 00010246 fs 0000 | Stack Trace follows:
00000000 600adf45
fc017f40 600d3bd7
fc017f54 600cf478
fc017f7c 600c4854
kdebug
when I sc, I get:
Stack back trace for thread 67
KERNEL -- frame retaddr
0x00000000 0x600adf45
0xfc017f40 0x600d3bd7
0xfc017f54 0x600cf478
0xfc017f7c 0x600c4854
I have BIOS set to Non PNP, set IRG for USB on its own. I am stump. Is there any other information I can provide for you. Thank you.
|
|
| f800802 |
|
|
By zharik - Posted on June 15, 2004 - 08:23:00 (#12881)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
This module doesn't know about files, directories and filesystems at all. It works on lower level with raw device data... Probably your msdos filesystem addon has a problem.
|
|
| Works fine |
|
|
By f800802 - Posted on June 14, 2004 - 12:20:08 (#12868)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
This patch works fine with:
Zeta
Tyan Tiger 2460 motherboard
SanDisk 1GB USB memory
The only problem i have is that the SanDisk is reconised as a DOS 16-bit volume, by this i am not alowed to copy files with long filesnames.
|
|
| ernestTX |
|
|
By zharik - Posted on June 14, 2004 - 08:16:32 (#12866)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
go to
/boot/home/config/add-ons/kernel/drivers/dev/printer/usb/
and run
ln -s ../../../bin/usb_printer
than go to
/boot/home/config/add-ons/kernel/drivers/dev/bus/usb/
and run
ln -s ../../../bin/usb_raw
|
|
| mario |
|
|
By zharik - Posted on June 14, 2004 - 08:15:02 (#12865)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
It will work with plain R5 _only_ after you update USB subsystem with those patches.
|
|
| Thanks s_d, I found it. Question: is it for BeOS 5.0.3? |
|
|
By mario - Posted on June 14, 2004 - 06:17:54 (#12864)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Or will it work with "pure" 5.0?
|
|
| still having problems following directions for usb patch |
|
|
By ernestTX - Posted on June 14, 2004 - 06:03:53 (#12863)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Forgive me, but I have tried instructions for usb patches several times. I do believe, I may be doing it wrong. I copied all files to appropriate places (i.e. addons/kernel/busses, drivers, etc.). However, the last steps to create sim link to ../dev/ is throwing me off. Could someone provide clear instructions on how to do this and where to place, copy files. I have ASUS A7V133 motherboard. What I have done has thrown me into KDL each time. Thank you.
|
|
| Re2: mario |
|
|
By s_d - Posted on June 13, 2004 - 19:46:33 (#12860)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Look this "forum" through. There is URL at first page.
|
|
| Anything else but beshare? |
|
|
By mario - Posted on June 13, 2004 - 19:43:18 (#12859)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Can't access Beshare due to router configuration....
|
|
| re: mario |
|
|
By Franxico - Posted on June 13, 2004 - 16:33:11 (#12858)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
You can find the patch on BeShare http://bebits.com/app/1330
|
|
| Re. s_d |
|
|
By mario - Posted on June 13, 2004 - 15:57:58 (#12857)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Allright, where do I find this patch? I can't find it on BeBits (I searched for "usb patch").
I know that dano has USB support in the kernel, but I didn't know there is a patch that would add the support to r.5.0
|
|
| Re:mario |
|
|
By s_d - Posted on June 13, 2004 - 13:30:19 (#12855)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
No, it don't
It needs updated USB stack (v.3) - so called USB.patches to be installed over vanilla R5 PRO.
|
|
| Vanilla BeOS r.5.0? |
|
|
By mario - Posted on June 13, 2004 - 12:53:56 (#12854)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Just to make sure: does this work with a vanilla BeOS r.5.0 (pro, in my case)?
|
|
| RE: BIOS |
|
|
By ryanknapper - Posted on June 12, 2004 - 20:08:52 (#12847)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Woo-hoo! I found an option in the VP6 BIOS to not assign an IRQ for USB. I enabled the IRQ and now BeOS can see the drive. I get a General OS Error when mounting, but it can see it.
:)
|
|
| Also |
|
|
By tqh - Posted on June 12, 2004 - 17:33:27 (#12844)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
Check that you have assign IRQ for USB and that USB doesn't share IRQ with something else.
|
|
| BIOS disabled USB |
|
|
By rudolfc - Posted on June 12, 2004 - 10:38:15 (#12840)
Current version when comment was posted: 0.1.0-alpha-1 |
|
|
H_ank,
Did you select:
PnP OS = false
in your system BIOS? If you have such an option and you did not set that, try this...
Rudolf.
|
|
|
|
|
|
|
|
|
 |
|
|
|
|
|
|
|
|
 |
| |
Recent Downloads - # 68
Total Downloads - # 155
Total Views - # 78
User Ratings - # 32
|
|
|
|
 |
| |
Misc. Drivers
Rem. Storage Drivers
|
|
|
|
 |
|
1. BePodder - 9.80
2. QEMU - 9.68
3. ScummVM - 9.57
4. cpu_fix - 9.42
5. Jukebox - 9.40
6. libdl.so - 9.40
7. Haiku AGP busm... - 9.35
8. vim6 - 9.31
9. Beezer - 9.26
10. HandBrake - 9.25
|
|
|
|
 |
|
1. BeOS 5 Perso... - 13,580
2. Realtek RTL8... - 13,095
3. Ati Radeon G... - 12,555
4. Ensoniq Audio... - 7,550
5. ATI Rage 128... - 7,436
6. USB Joystick... - 5,656
7. Broadcom 440x... - 5,405
8. S3 Trio 64 v2... - 4,715
9. USB Serial dr... - 4,704
10. Intel Extreme... - 4,465
|
|
|
|
 |
| You are not logged in.
Login
|
|
|
|
 |
|
